Start-MigrationBatch

This cmdlet is available in on-premises Exchange and in the cloud-based service. Some parameters and settings may be exclusive to one environment or the other.

Use the Start-MigrationBatch cmdlet to start a move request or migration batch that was created with the New-MigrationBatch cmdlet.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

Start-MigrationBatch
     [[-Identity] <MigrationBatchIdParameter>]
     [-Confirm]
     [-DomainController <Fqdn>]
     [-Partition <MailboxIdParameter>]
     [-Validate]
     [-WhatIf]
     [<CommonParameters>]

Description

The Start-MigrationBatch cmdlet starts a pending migration batch that was created, but not started, with the New-MigrationBatch cmdlet.

The Start-MigrationBatch cmdlet also will resume a Stopped migration batch or retry failures within a Failed or Synced with Errors migration batch. In the cloud-based service, the Start-MigrationBatch cmdlet can also retry failures within a Completed with Errors migration batch.

In the cloud-based service, the Start-MigrationBatch cmdlet can be run at any time to retry failed users within the batch.

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

Start-MigrationBatch -Identity SEM1

This example starts the migration batch SEM1.

Parameters

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Type:SwitchParameter
Aliases:cf
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

-DomainController

This parameter is available only in on-premises Exchange.

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

Type:Fqdn
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-Identity

The Identity parameter identifies the migration batch that you want to start. Use the migration batch Name parameter as the value for this parameter. Use the Get-MigrationBatch cmdlet to identify the name of the migration batch.

Type:MigrationBatchIdParameter
Position:1
Default value:None
Required:False
Accept pipeline input:True
Accept wildcard characters:False
Applies to:Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

-Partition

This parameter is available only in the cloud-based service.

This parameter is reserved for internal Microsoft use.

Type:MailboxIdParameter
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Online

-Validate

This parameter is available only in on-premises Exchange.

The Validate switch starts the migration batch in the validation stage of the migration process. You don't need to specify a value with this switch.

If you use this switch, the migration performs a validation check of the mailboxes in the batch.

Type:SwitchParameter
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:SwitchParameter
Aliases:wi
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

Inputs

Input types

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.

Outputs

Output types

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.